l i n u x - u s e r s - g r o u p - o f - d a v i s
L U G O D
 
Next Meeting:
November 4: Social gathering
Next Installfest:
TBD
Latest News:
Oct. 10: LUGOD Installfests coming again soon
Page last updated:
2002 Aug 23 17:54

The following is an archive of a post made to our 'vox-tech mailing list' by one of its subscribers.

Report this post as spam:

(Enter your email address)
Re: [vox-tech] Wireless card configuration
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [vox-tech] Wireless card configuration



This is just an additional note.  Everything mentioned here worked for me
back with RH 7.1, so I don't know any reason why it shouldn't also exist
in 7.2.  I run slackware, and have my own specially compiled versions of
the kenrel, pcmcia, and wireless tools.  However, in RH if
kenrel-pcmcia.rpm (or whatever the exact name) is installed, you should
really be good to go.  It's just a matter of configuring the scripts
mentioned in shawn's message below to correctly talk to your router.  I'm
using an all D-link setup, so I can't comment there, but Shawn is right on
target.  You may need to set SSID or ESSID (you'll see both when flipping
through various wireless docs).  Remember that the silver only supports
40/64 bit WEP.  I don't use WEP at home, but I configure my router to only
talk to the nics/ips I specify.  So my airbourne traffic isn't safe from
interception, but nobody else can asscociate with my router.  Be careful,
if WEP is off and DHCP is on, and your SSID is "default" or "any" anybody
can hop onto your network.  The web-based interfaces for the router make
things easy, but be careful as there are a lot of things you can
do wrong (association settings, DHCP allowances, etc.).

Here's one other note: I've already sent two DWL-650s back to D-Link.
If you think you've done everything right, the
card could always be fried?  Proceed as if it isn't as the chances are
likely slim, but keep the thought in mind.

Good luck and have fun with your wireless setup.

Dave

On Thu, 22 Aug 2002, Shawn P. Neugebauer wrote:

> Alan,
>
> Welcome.
>
> As a first comment, I suggest moving to RH 7.3.  If you were running it now,
> I would suggest you run redhat-config-network and follow the instructions
> at
> http://www.redhat.com/docs/manuals/linux/RHL-7.3-Manual/custom-guide/s1-network-config-wireless.html
> My Orinico worked almost out-of-the-box with RH 7.3.  Part of the ease
> was that I was communicating with an already-configured router.
>
> I'll try to offer some helpful comments (possibly helpful to others).  Feel
> free to follow-up in email.  Unfortunately, I'm writing this note in a place
> where I am not able to verify my comments in a hands-on manner.
> What you will read is a combination of notes (written by myself and
> from others), memory, and a little bit of poking around.
>
> Before proceeding, make sure you understand the configuration of your
> wireless router.  I can't offer too many specifics here (I'm not familiar with
> the router you are using), but you are looking for:  keys, the ESSID,
> any router-specific configuration that needs to be performed to permit
> a wireless device to connect, any DHCP configuration that needs to be
> performed, etc.  Also, does the router supply DNS information to the
> remote device?  Lots of things that might appear to be a problem
> on the RH/Orinico side could actually be problems on the router side.
> Make sure you have a way to get access to log info in the router.
>
> You should not need to install software, but this might depend on the
> type of installation you did (I'm not sure).  The two key packages are:
> kernel-pcmcia-cs and wireless-tools.  Both should be distributed
> on the RH disks, and you need only find the packages and do
> "rpm -ivh <pkgname>" to install each.  You shouldn't have to build
> either of these from source, although you might want to get a more
> up-to-date version from the RH errata site, if available, or find more
> up-to-date versions elsewhere on the net.  The kernel-pcmcia-cs
> package includes basic support for PCMCIA cards, and useful
> commands like cardctl (typically installed in /sbin/), good for
> "cardctl eject" or "cardctl ident" or "cardctl config" etc.  The
> wireless-tools package has useful commands like iwconfig, iwspy,
> and iwlist.  You may become acquainted with the first command.
>
> I also did not think you had to install an orinico driver--I thought it
> was built-in (I know it is supplied with RH 7.3).  You'll know in a
> moment.
>
> With this software installed, insert the card.  You should get 2
> pleasant beeps.  The green light will start flashing--it's looking
> for a base station.  The "dmesg" command should show the
> right card, automagically detected.  The "lsmod" command should
> should an orinico-related driver.  The light turns solid when the
> card establishes an ethernet connection with the wireless router,
> but you probably will not be able to connect with anything, yet.  If these
> parts (all but the solid light) aren't working correctly, get them going
> before moving to the rest.
>
> Since you have one card already installed, the second card
> will use the "eth1" interface (typically, the first card
> picks up "eth0"--keep this in mind for later discussions).  The
> "/sbin/ifconfig" command will list the active interfaces.  You
> may or may not see the second interface there, yet,
> depending on your configuration.
>
> Assuming you do not see two interfaces, you've got some
> configuration to do.  Remove the card after typing "cardctl eject".
>
> You have two options for supplying the configuration options
> needed to establish the link.  First, /etc/pcmcia/wireless.opts.
> Find the second for Orinico, and change what needs to be
> changed, based on your investigation of the router (e.g.,
> key, ESSID, etc.).  Second, you can supply this information
> on the cmdline using the "iwconfig" command.  I've used
> both.  The obvious advantage to the first method is automation.
>
> You also need to supply some interface options.
> In /etc/sysconfig/network-scripts, copy ifcfg-eth0 to
> ifcfg-eth1.  Edit it; should look like:
>   DEVICE="eth1"
>   ONBOOT="no"
>   BOOTPROTO="dhcp"
>   TYPE="Wireless"
>
> With these mods, the pcmcia scripts should attempt, upon
> card insertion, to automatically load the correct driver (you already
> established this), configure the wireless interface, and get an IP address
> via DHCP.  If the system succeeds in doing these things, you
> will see a second interface with ifconfig.  Furthermore, if the DHCP
> server supplies DNS information, you will see that your
> /etc/resolv.conf file has been replaced.  At this point, you should
> be well on your way.  You should be able to ping the router, ping
> another machine on the network, ping the DNS servers (probably
> outside your home), do DNS lookups, etc. (roughly in that order).
>
> I have in the past needed to run dhcpcd, the DHCP client daemon,
> manually (dhcpcd eth0) to get the last bit going.  But, this should
> be automated in current RH distributions, with proper configuration.
>
> Note that in the last part, your DNS information was temporarily
> overwritten by DHCP-supplied results.  Unless you do additional
> work to your configuration, the act of inserting the wireless card
> will cause the wireless interface to temporarily override the
> wired interface.  However, the wired interface should be restored,
> effectively (it was never really removed), when the card is ejected.
> Since both interfaces are communicating with the same gateway,
> I don't think this matters.  However, there are potential complications
> in this that might need to be worked out (this is the domain of route--
> routing tables, default gateways, etc.).
>
> I think this is enough to get you going in the correct direction.
>
> shawn.
>
> p.s. most of the relevant links i had are out-dated, so i'm not supplying
> any here.  but i know there are lots of small "how-to"-type sites out
> there that discuss the combination of RH and Orinico--it's very
> popular.
>
>
>
> On Thursday 22 August 2002 02:07 pm, Alan H. Lake wrote:
> > Preliminary:
> > This is my first posting to this site.  I set up Evolution, hopefully,
> > so that this posting is not HTML.  If it does arrive as HTML, please
> > don't flame me, just inform me.
> >
> > --------
> >
> > Summary: I need to configure my Orinoco Silver wireless PCMCIA card so
> > that it will talk with my Linksys router.
> >
> > Details:
> > I connect to the Internet via cable broadband.  My cable modem is
> > connected to a Linksys "Etherfast Wireless Access Point + Cable/DSL
> > Router with 4-Port Switch".  This router uses DHCP assigned addresses.
> > The router has attached to it (via cable) a Win98 computer and my
> > laptop, which runs Red Hat 7.2.
> >
> > I have two PCMCIA cards for my laptop.  The first card is a Linksys
> > Etherfast 10/100 + 56K modem.  I use the Ethernet cable to connect to
> > the router.   Works fine.  The other card is an Orinoco Silver wireless
> > network card.
> >
> > I have downloaded files and compiled a module to make the Orinoco card
> > work.  The PCMCIA appears to function OK.  What I don't have working is
> > the wireless configuration whereby the wireless card talks to the
> > router.
> >
> > I've been struggling with this problem since April.  While doing so, I
> > have managed to screw up my PCMCIA so that I had to reinstall my OS
> > (because I didn't understand exactly what I was doing.)  Because all of
> > my network connections are PCMCIA, I am afraid of doing something that
> > will make neither card work, which means that I can't connect to the
> > Internet, ask for help or anything.  (I've already done that once.)
> >
> > Will someone please correspond with me to confirm that both PCMCIA cards
> > are indeed working correctly, then help me to examine my router settings
> > and settings in /etc/pcmcia files so that I might get my wireless to
> > work.  Of course, I allow that there may be a setting somewhere else
> > that I also need to set.
> >
> > Another thing I'd like to be able to do, if it's not a big deal, is to
> > set up communications from my laptop to the Win98 machine.  I have
> > VMWare and have run several Windoze machines under it, including Win98.
> > This means that I have messed with Samba, although I can't claim to be a
> > Samba expert.
> >
> > Thanks, all.
> > Alan
> >
> >
> >
> >
> >
> >
> > _______________________________________________
> > vox-tech mailing list
> > vox-tech@lists.lugod.org
> > http://lists.lugod.org/mailman/listinfo/vox-tech
>
> _______________________________________________
> vox-tech mailing list
> vox-tech@lists.lugod.org
> http://lists.lugod.org/mailman/listinfo/vox-tech
>

_______________________________________________
vox-tech mailing list
vox-tech@lists.lugod.org
http://lists.lugod.org/mailman/listinfo/vox-tech



LinkedIn
LUGOD Group on LinkedIn
Sign up for LUGOD event announcements
Your email address:
facebook
LUGOD Group on Facebook
'Like' LUGOD on Facebook:

Hosting provided by:
Sunset Systems
Sunset Systems offers preconfigured Linux systems, remote system administration and custom software development.

LUGOD: Linux Users' Group of Davis
PO Box 2082, Davis, CA 95617
Contact Us

LUGOD is a 501(c)7 non-profit organization
based in Davis, California
and serving the Sacramento area.
"Linux" is a trademark of Linus Torvalds.

Sponsored in part by:
Appahost Applications
For a significant contribution towards our projector, and a generous donation to allow us to continue meeting at the Davis Library.